Scientific extension Space Engineering/Space Orbit Mechanics/Space Sciences/...
Introduction to Space Debris Capturing Methods

Alireza Nazari Karadeh; Alireza Alikhani; Milad Azimi

Volume 7, Issue 1 , April 2023, Pages 1-16

https://doi.org/10.30699/jtae.2023.7.1.1

Abstract
  Space debris is considered a serious problem for space operational missions. Many methods of capturing space debris have been proposed in the last decade and have been tested by various ground-based and sub-orbital flight methods. Space debris is usually an unusual and unknown object, and capturing and ...  Read More

Scientific extension Life Sciences/Environment/Plant Physiology/Animal Physiology/Remote Sensing/...
Investigation of plant cell culture models for space studies

Halimeh Hassanpour

Volume 7, Issue 1 , April 2023, Pages 17-23

https://doi.org/10.30699/jtae.2023.7.1.2

Abstract
  The selection of suitable biological sample for space studies has vital importance. Plant cell suspension culture containing a homogenous population of proliferating cells prepares the proper situation to study various cell responses under stress conditions, especially microgravity. Cell culture systems ...  Read More

Research Note Propulsion/Thermodynamics/Heat Transfer/Fuel and Combustion/Energy/...
Simulation of the Bypass Dual Throat Nozzle and investigation of parameters affecting the change of thrust vector angle

Amir Mohammad Neyzan Hosseini; Hossein Mahdavy-Moghaddam

Volume 7, Issue 1 , April 2023, Pages 25-33

https://doi.org/10.30699/jtae.2023.7.1.3

Abstract
  The aim of this study was to investigate the effects of three parameters including secondary flow injection angle, secondary flow injection location and bypass section geometry on the deflection angle of the thrust vector. The model is simulated in both two and three dimensional for a Dual Throat Nozzle. ...  Read More

Research Article Structure/Solid Mechanics/Solid Dynamics/Vibrations/Aeroelasticity/...
Experimental Investigation on low cycle Fatigue Behavior of Al6061/SiC composite Fabricated by Friction Stir Processing

Mohammad Jelokhani Niaraki; hossein torabian; Simin kamali rousta

Volume 7, Issue 1 , April 2023, Pages 35-43

https://doi.org/10.30699/jtae.2023.7.1.4

Abstract
  According to friction stir processing For production of surface composites with constant progress and rotational speed, samples are made in different number of passes (1,3.5) and to obtain the stress range and adjust the device and apply the fatigue and tensile test is performed. Results of micro-structure ...  Read More

Research Article Structure/Solid Mechanics/Solid Dynamics/Vibrations/Aeroelasticity/...
Investigation of the effect of parameters of a nonlinear dynamic absorber on reducing the vibration amplitude of a nonlinear system

Mohammad Mahdi Nazari; Abbas Rahi

Volume 7, Issue 1 , April 2023, Pages 45-55

https://doi.org/10.30699/jtae.2023.7.1.5

Abstract
  Purpose of paper is to use a nonlinear dynamic absorber as beam with concentrated mass at its end to reduce the amplitude of resonant nonlinear oscillator vibration. Primary vibration system consists of mass, nonlinear spring, and viscous damping, and harmonic force is applied to it and causes the system ...  Read More

Research Article Structure/Solid Mechanics/Solid Dynamics/Vibrations/Aeroelasticity/...
Flutter analysis of a CNT-reinforced composite beam carrying an attached mass in the supersonic flow

Reza Maboodi; Hassan Shokrollahi; Mostafa Esmaeili

Volume 7, Issue 1 , April 2023, Pages 57-67

https://doi.org/10.30699/jtae.2023.7.1.6

Abstract
  In this paper, the flutter analysis of a CNT-reinforced composite beam carrying an attached mass in the supersonic flow under different boundary conditions is presented. Also, the analysis of the mentioned beam has been investigated taking into account of the first-order shear deformation theory. The ...  Read More