فناوری در مهندسی هوافضا

فناوری در مهندسی هوافضا

ارزیابی کاهش درگ پوسته‌ای در هندسه‌ های سرپخ با استفاده از ریزساختارهای سطحی

نوع مقاله : علمی پژوهشی

نویسندگان
1 تهران- شهرک قدس (غرب)، خ ایران زمین، خ مهستان، خ پژوهشگاه هوافضا
2 پژوهشگاه هوافضا
10.22034/jtae.2026.541833.1411
چکیده
موضوع مورد نظر تحقیق حاضر بررسی عددی پوشش‌هایی با ساختار میکرو به منظور کاهش درگ پوسته‌ای در هندسه های مختلف کانال دارای ریزساختارهای (شامل مربع، مثلث، ذوزنقه و نیم‌دایره) می‌باشد. در تحقیق حاضر ابتدا به بررسی میکروساختارهای مختلف به منظور یافتن شکل بهینه ساختارها برای بیشترین کاهش درگ پرداخته می‌شود. سپس مطالعه پارامتریک هندسه‌های منتخب ریزساختارها در راستای بهبود کاهش درگ بصورت عددی مدنظر قرارگرفته است. این متغیرهای هندسی شامل ارتفاع و پهنا و همچنین فاصله بین ریزساختارها می‌باشند. نتایج شبیه سازی جریان حاصل از تغییرات پارامترهای هندسی مذکور به طور مجزا در ساختارهایی با هندسه های مختلف بررسی می‌شود و با تحلیل کانتورهای سرعت و فشار و خطوط جریان، نتایج نهایی شامل درگ پوسته‌ای، کل و همچنین ضریب اصطکاک فیزیک حاکم بر مساله استخراج شده و ابعاد مناسب برای ریزساختاری که بیشترین کاهش درگ پوسته‌ای را به همراه می‌آورد به دست می‌آید. بعد از انجام شبیه سازی‌های ذکر شده مشخص می‌شود که ساختار مربعی در یک ابعاد مشخص بیشترین کاهش درگ پوسته‌ای را به همراه دارد که این ساختار منتخب در یک هندسه‌ی سر پخ دوبعدی بکار برده شده و نتایج حاصل از حضور ریزساختار با هدف کاهش درگ پوسته‌ای بررسی می‌شود. مطالعه حاضر نشان داد که از بین سه حالت هندسه بدون ریزساختار، هندسه دارای ریزساختار در قسمت استوانه‌ای و هندسه دارای ریزساختار در تمام سطح، بیشترین کاهش درگ پوسته‌ای برابر با 4/67% و مربوط به حالت سوم می‌باشد.
کلیدواژه‌ها
موضوعات

عنوان مقاله English

Asessment of friction drag reduction in blunt bodies using surface microstructures

نویسندگان English

Ramin Moghadam 1
Maral Rastegar 2
Mohammadjavad kahalian 2
1 هیات علمی
2 Aerospace Research Institute
چکیده English

The research is the numerical investigation of micro-structure coatings with different geometries (including square, triangular, trapezoidal and semicircular) to reduce friction drag on the channel surface. In the present research, firstly, different microstructure geometries are examined in order to find the optimal shape of the structures for the maximum drag reduction. Then, the parametric study of selected geometries of microstructures has been numerically considered in order to improve drag reduction. These geometric variables include height and width as well as the pitch. The obtained simulation results from the changes of the mentioned geometric parameters are separately examined in the structures with different geometries. By analyzing the velocity and pressure contours and flow stream lines, the total drag and also friction coefficient are extracted and appropriate dimensions are obtained for the microstructure that brings the greatest reduction in friction drag. Based on the results, it is clear that the square structure in a certain dimension has the greatest reduction in friction drag, and this selected structure has been used on a 2-D blunt body geometry. The results showed that among the three cases geometry without microstructure, geometry with microstructure on the cylindrical section, and geometry with microstructure on the entire surface, the highest reduction in friction drag was 67.4% and related to the third case.
. . . . . .

کلیدواژه‌ها English

Surface Micro-Structure
Friction Drag Reduction
Numerical Simulation
Drag optimization

مقالات آماده انتشار، پذیرفته شده
انتشار آنلاین از 26 آبان 1405

  • تاریخ دریافت 26 مرداد 1404
  • تاریخ بازنگری 14 مهر 1405
  • تاریخ پذیرش 21 مهر 1405
  • تاریخ اولین انتشار 26 آبان 1405